loop n. 1.(用线、带等打成的)圈,环,匝,框,环孔,线圈;【医学】(常 the loop)宫内避孕环。 2.环状物,塔环,拎环。 3.(铁路上的)让车道,环道。 4.【无线电】回路,回线,波腹,环形天线。 5.【数学】自变;【计算机】循环;(程序中)一群指令的重复。 6.【航空】翻圈飞行,翻筋斗;【溜冰】(单脚)打圈儿。 7.〔美国〕闹市区;〔the L-〕 芝加哥的商业区。 a safety loop保险圈。 a wire loop钢丝套圈。 knock [throw] for a loop 〔美俚〕 1. 使神志不清;打昏,使醉倒。 2. 给人极好的印象。 3. 出色地通过[做成]。 on the loop 〔美国〕在匆匆旅行中。 out of the loop 在圈内人物之外的,不在…圈子内的。 vt. 1.使(绳等)成圈,打成圈;【电学】 把导线连成回路。 2.用圈围住;(用环)箍住。 (up back). 3.使作成环状运动;【航空】翻筋斗。 vi. 1.打环,成圈。 2.【航空】翻筋斗。 3.(像尺蠖似的)伸屈前进。 loop the loop 【航空】翻筋斗;(骑自行车等)兜圈子。
Analysis of signal character of magnetic flux leakage testing using loop method 线圈法漏磁探伤的信号特性分析
Rubber or plastics coated fabrics determination of flexibility - flat loop method 橡胶或塑料涂覆织物.柔软性的测定.扁环法
Motion analysis of the dual - elbow - bar mechanism of the die - cutting machine based on the loop method 基于回路法的模切机双肘杆机构运动分析
The development is consists with the thinking of software engineering and the loop method of prototype 文中对系统的硬件和软件解决方案进行了详细的讨论。
A feedforward or open loop method is used to estimate the parameters , and then more accurate feedback or closed loop method is used to complete synchronization 首先利用前向估测方法对参数进行预估计,在此基础上结合后向反馈方法完成同步。
By means of the multi - loop method , the steady - state analysis of internal faults in stator windings of synchronous machine has been made , but as to the transient analysis , research only limited to single machine with no - load 运用多回路方法,已经基本解决了同步电机内部故障的稳态分析问题,但对故障的暂态研究,以前还仅限于单机空载的情况。
Regarding the discrete magnetic vector potential and loop currents as the state variables , and combining the fem with the multi - loop method , a mathematical model of the synchronous machine with internal faults is set up in this paper 本文以矢量磁位和回路电流为求解变量,把电机的电磁场方程与反映绕组联接情况的电路方程联立起来同时求解,提出了同步发电机定子绕组内部故障的瞬态电磁场与多回路耦合的数学模型。
The paper ' s contents involve the following aspects : 1 based on the multi - loop method , this paper describes the construction of a mathematical model of salient - pole synchronous generators suitable for analyzing the transient behavior of internal faults in stator windings 本文针对发电机定子绕组内部故障暂态分析中存在的一系列问题,开展了研究工作,主要内容有: ( 1 )建立了凸极同步发电机定子绕组内部故障暂态计算的多回路数学模型。
To solve the poor precision problems of dataglove angle outputs , this paper builds human hand kinematic model and fingertip position error model , and gets the precise parameters of human hand model by the parameters identification based on fingertip positions closed loop method 本文针对数据手套关节角度输出精度低等缺点,建立了人手的运动学模型和各指尖位置的误差模型。基于指尖位置闭环的方法完成了人手模型的参数识别,提高了人手模型几何参数的精度,得到了较精确的人手手指指尖位置。